Round hot tub with slightly cloudy blue water, a warm stone rim and palms behind it

Problems and fixes

Hot Tub Cloudy After Shock? How to Clear It

Hot tub cloudy after shock? Why the water stays hazy, what to test, how to clear it step by step, and when a drain and refill is the better fix.

Jump to the calculator

On this page
  1. Why shock can leave a hot tub cloudy
  2. How to clear it, step by step
  3. Chlorine and bromine tubs differ
  4. How to keep it from happening again
  5. Common mistakes
  6. Track it in Spa Calc
  7. Sources
  8. Safety

The quick answer: a hot tub that's cloudy after shock usually isn't finished: the shock has broken down waste, and the filter still has to catch what's left. Test sanitizer, pH and alkalinity, clean the filter, and run the circulation. If it's still cloudy the next day, work through the steps below. Follow the product label for anything you add.

All-in-one hot tub calculator

gal

Not sure? Find your tub’s volume.

ppm
ppm
ppm
ppm
ppm

Dichlor adds it. Blank if you have not tested.

°F
%

Not safe: do not get in yet.

Two things to fix. Start with ph.

  1. pH 7.9 → 7.5

    Lower it

    Add

    0.42oz

    of Dry acid / pH minus (sodium bisulfate 93%)

    12 gabout 2⅛ tsp by volume

    • Side effects: TA −3 ppm.
    • Run the jets with the lid open and wait at least 15 minutes (20 after pH decreaser) before anyone gets in.
    • Never add acid and chlorine together or in the same spot: mixing them releases toxic chlorine gas. Let the first one circulate before adding the other (the wait is shown on each step).

    Then wait 15 minutes with the jets running.

  2. Free chlorine 1 ppm → 4 ppm

    Raise it

    Add

    0.29oz

    of Dichlor granules 56%

    8.1 gabout 1⅞ tsp by volume

    • Side effects: CYA +2.7 ppm, TA −1.1 ppm.
    • Also raises cyanuric acid (stabilizer). It only comes down by replacing water.
    • Run the jets with the lid open and wait at least 15 minutes (20 after pH decreaser) before anyone gets in.
    • Free chlorine is below the minimum for your stabilizer level.
    • Use dichlor for the first week or two until stabilizer reaches about 30 ppm.

In range

  • CYA 20 ppm
  • TA 70 ppm
  • Use dichlor for the first week or two until stabilizer reaches about 30 ppm.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

  • CDC recommends not using stabilizer (cyanuric acid) in hot tubs, because it slows chlorine down. The dichlor-then-bleach method keeps it to about 30 to 40 ppm; bleach only keeps it at zero.

Save this test and get a reminder before your next soak.

Download on the App Store

Why shock can leave a hot tub cloudy

Most of the time, one of these is going on:

  • Waste the shock has broken down. One maker's manual names body oils, lotions and fine particles as the two main causes of cloudy water. A shock deals with the oils, but particles still have to reach the filter.
  • A dirty filter. Hot Spring's owner guidance lists dirty filters first among the causes of cloudy water. A shock can't clean a cartridge.
  • Sanitizer that's still too low. If a heavy load used up the shock, the job isn't done. CDC recommends at least 3 ppm chlorine in hot tubs.
  • High pH or alkalinity. Taylor Technologies explains that water on the scaling side can hold suspended calcium carbonate, which looks cloudy. TroubleFreePool warns that high alkalinity in a hot tub can bring scaling and cloudiness.
  • A calcium-based shock. TroubleFreePool notes that cal-hypo can cloud water when alkalinity is high, and it raises calcium hardness with continued use.
  • Old water. Hot Spring also lists "overused or old water." No shock fixes that for long.

How to clear it, step by step

Step 1: Test before you add anything. Check free chlorine or bromine, pH and alkalinity. TroubleFreePool's advice is not to add chemicals without knowing they're needed, and a second shock on top of a high reading only lengthens the wait. Note the reading in Spa Calc for iPhone, so you can see whether it's moving.

Test strips beside their closed container on a warm stone rim

Step 2: Clean the filter. Rinse the cartridge with a hose, then soak it in filter cleaner to lift oils, following your tub's manual. TroubleFreePool's basic guide says to rinse often and soak each time you drain. Replace a cartridge that won't come clean. Put it back and run the pump.

Step 3: Fix pH and alkalinity. If either is high, bring it down first in small steps, using pH decreaser as the label directs. The pH and alkalinity calculator works out the dose for your readings, so we don't give a fixed amount here. Hot tub pH too high has the detail.

Three glass test vials and a plain dropper bottle on a stone rim beside blue-teal water

Step 4: Bring sanitizer back into range. Aim for 3 to 5 ppm chlorine, or 4 to 6 ppm bromine. To raise chlorine from 2 to 4 ppm in 400 gallons takes about 5.4 g of 56% dichlor, or 1.7 fl oz (49 mL) of 6% bleach. US household bleach is sold at 6–8.25%, so use the chlorine calculator with the percentage on your label. CDC recommends not using cyanuric acid or products that contain it, such as dichlor, in hot tubs. Bleach adds none, if you'd rather avoid it.

Step 5: Give the filter time, then look again. Run the circulation with the cover open for a while. Look the next day: the water should be better. A clarifier can help the filter catch fine particles. It won't fix low sanitizer or bad balance, and Taylor says clarifiers aren't a long-term solution. If you use one, follow the product label.

Two glasses of water on a stone rim, one clear and one cloudy

Step 6: If it's still cloudy, drain and refill. When the readings are right and the filter is clean, the water is usually the problem. Hot Spring lists draining, cleaning and refilling among the fixes, and a refill often costs less than chasing it with more chemicals. At 2 soakers a day, a 400-gallon tub is due about every 67. How often to drain a hot tub explains the math.

Round hot tub with clear blue water, a stone rim, rolled towels and palms behind it

Chlorine and bromine tubs differ

Chlorine tubs. If you shocked with a large chlorine dose, wait for it to fall before soaking. A clear tub with a high reading isn't ready either. See hot tub chlorine too high.

Bromine tubs. Non-chlorine shock (MPS) turns bromide back into bromine, so the reading can jump. Test bromine after a shock, as hot tub shock: how long to wait explains.

When can you soak? First clear the water. Then test: Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels.

How to keep it from happening again

  • Test before each soak, and dose after soaks rather than waiting for a big fix.
  • Keep a clean spare cartridge, and rinse the filter often.
  • Keep alkalinity and pH in range, especially in hard-water areas.
  • Drain on schedule, before the water gets too old to hold its clarity.

Common mistakes

  • Shocking again right away. If the filter is clogged or the water is on the scaling side, more shock won't clear it.
  • Closing the cover too soon. One registered dichlor label says to let the spa circulate for 15 minutes after adding a dose before closing the cover.
  • Using a pool-size dose. A tub is a small volume of water, so small errors move the reading a long way.
  • Skipping the log. Spa Calc keeps tests and doses in one place, so you can see whether the haze follows high pH, low sanitizer or old water.

For haze that isn't linked to a shock, see cloudy hot tub water. If it turned green, see hot tub green water. If the water is also foaming, see hot tub foam.

Track it in Spa Calc

Spa Calc sizes each dose for your tub's volume and product, keeps your readings in one log, and shows whether your water is ready to soak. Get Spa Calc for iPhone and log your next test.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

Why is my hot tub cloudy after shock?

A shock breaks down oils and other waste, and the filter still has to catch what's left. If the haze lasts, the usual causes are a dirty filter, too little sanitizer, high pH or alkalinity, or old water. Test first, then clean the filter.

Why is my hot tub still cloudy after shock?

Look at what the shock couldn't fix: a clogged filter, scale-forming water or water that's simply old. Hot Spring's owner guidance lists dirty filters, excess oils, poor sanitizing, suspended particles and overused water as causes of cloudy water, and draining, cleaning and refilling as one of the fixes.

Should I shock my hot tub again if it's still cloudy?

Only if your test says so. Check sanitizer, pH and alkalinity, and clean the filter first. A second shock won't help a clogged filter or scaling, and adding calcium-based shock when alkalinity is high can make the haze worse.

Can I use my hot tub if it's cloudy after shock?

Treat it first. One hot tub maker's manual says cloudy, off-color or foamy water should be treated or drained before use. Once it's clear, test: Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels.

Why is my hot tub foaming after shock?

Foam usually points to oils, soaps or old water, not to the shock itself. Clean the filter, check your sanitizer, and see our guide to hot tub foam.

Save this guide

Hot Tub Cloudy After Shock? How to Clear It: illustrated Spa Calc guide card

Download this guide as an image