Problems and fixes

Hot Tub Smells: What Each Smell Means and How to Fix It

Hot tub smells musty, like chlorine or just bad? What each smell usually means, what to test, and how to fix it with a shock, a sanitizer top-up or a fresh fill.

Jump to the calculator

On this page
  1. Test first
  2. What each smell usually means
  3. How to fix it, step by step
  4. How to keep the smell from coming back
  5. When can you get in?
  6. Common mistakes
  7. Track it in Spa Calc
  8. Sources
  9. Safety

The quick answer: when a hot tub smells, the water is telling you something. A strong "chlorine" smell usually means combined chlorine (chloramines), not too much chlorine. A musty or "off" smell usually means the sanitizer has run low and organics or growth have built up. In both cases the fix is the same start: test free chlorine (or bromine) and pH, shock the tub, and bring pH back into range. If the smell keeps coming back, drain, clean and refill. Follow the product label for every chemical you add.

The chlorine calculator below works out how much of your product it takes to reach the level you need.

Hot tub chlorine calculator

gal

Not sure? Find your tub’s volume.

%
ppm

Fresh water: 0. Dichlor raises it about 0.9 ppm per 1 ppm of chlorine.

ppm
ppm

Set from your CYA until you change it. Hot tubs: 3 to 5 ppm (CDC minimum 3; many labels say not to soak above 5).

Add

0.29oz

of Dichlor granules 56%

8.1 gabout 1⅞ tsp by volume

Raises free chlorine from 1 ppm to 4 ppm in 400 gal.

  • Side effects: CYA +2.7 ppm, TA −1.1 ppm.
  • Also raises cyanuric acid (stabilizer). It only comes down by replacing water.
  • Run the jets with the lid open and wait at least 15 minutes (20 after pH decreaser) before anyone gets in.
  • Pour it slowly in front of a return jet with the pump running.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

Use dichlor for the first week or two until stabilizer reaches about 30 ppm.

Save this test and get a reminder before your next soak.

Download on the App Store

Test first

Before you add anything, test:

  • Free chlorine (or bromine in a bromine tub). CDC recommends at least 3 ppm chlorine in hot tubs. CDC's hot tub toolkit uses 3–10 ppm free chlorine or 4–8 ppm bromine as control limits for public hot tubs.
  • Total chlorine. Combined chlorine = total chlorine minus free chlorine, as CDC explains. A noticeable gap means chloramines.
  • pH. CDC's hot tub toolkit uses 7.2–7.8.
  • CYA, if you use dichlor. CDC recommends not using cyanuric acid or chlorine products with cyanuric acid in hot tubs, and we suggest draining once it is above 40 ppm.

Logging the results in Spa Calc for iPhone keeps each reading next to the last one, so a slow slide in sanitizer shows up before the smell does.

What each smell usually means

One hot tub maker's owner troubleshooting chart (Hot Spring Spas) groups smells into three kinds. Their causes line up with what CDC says about chloramines.

Smell Usual causes What to do
Strong "chlorine" or chemical smell Chloramines too high; low pH Shock; correct pH
Musty, mildew Bacteria or algae growth Shock; if visible or persistent, drain, clean and refill
General bad or "off" smell (often described as fishy or sour) Too many organics; not enough sanitizer; low pH Shock; add sanitizer; correct pH; drain, clean and refill if needed

"My hot tub smells like chlorine"

This one surprises people. CDC explains that if you smell "chlorine" at a pool, you are probably smelling chloramines: irritants that form when chlorine combines with sweat, dirt, skin cells, deodorant, makeup and other things that wash off bathers. That also leaves less chlorine to kill germs. So a chlorine smell is usually a sign of too little working chlorine for the load, not too much.

The fix is a shock (below) and a pH check. Adding just a little more chlorine at the normal level often isn't enough to clear it. If your free chlorine reading itself is high, see hot tub chlorine too high instead.

"My hot tub smells musty"

A musty or mildew smell points to growth in the water or the plumbing. Shock with sanitizer and keep the level in range afterwards. If you can see slime, or the smell returns within days of a shock, the water and the surfaces need a full drain, clean and refill. CDC's hot tub toolkit lists sediment and biofilm among the things that let germs grow, and says to scrub all surfaces vigorously each time the tub is drained.

"My hot tub smells bad" (fishy, sour, swampy)

People describe it in many ways, but the chart treats them the same: too much organic material and not enough sanitizer, sometimes with low pH. Shock, top up sanitizer, correct pH, and check when the water was last changed. Old water carries more of everything that bathers leave behind; how often to drain a hot tub shows how to work out your interval.

If the water smelled straight after a fresh fill, before anyone used the tub, the fill water itself may be the source. Test it, and ask your water supplier.

How to fix it, step by step

  1. Correct pH into 7.2–7.8. If it's low, see hot tub pH too low; if it's high, hot tub pH too high. We don't give a fixed acid dose for pH, because it depends on alkalinity; the pH and alkalinity calculator works it out for your tub.
  2. Shock the water. With no stabilizer in the water, the shock level is 10 ppm free chlorine. In a 400 gallon tub, raising free chlorine from 1 to 10 ppm takes about 7.4 fl oz (220 mL) of 6% household bleach, or about 5.2 fl oz (155 mL) of 8.25% bleach. US household bleach is sold at 6% to 8.25%, so use the chlorine calculator with the percentage on your label, and use plain, unscented bleach. With 56% dichlor it's about 0.86 oz (24 g), but dichlor adds stabilizer. Follow the product label.
  3. Run the jets with the cover open for a while so gases can escape.
  4. Test again. Free chlorine should come back down into range before anyone soaks, and the smell should fade as the chloramines break down.
  5. If the smell returns within days, or you can see slime, drain, clean and refill. Clean or service the filter the way its maker recommends.

Bromine tubs: the same causes apply. Shock to regenerate bromine and break down the organic load, then test bromine before soaking. Hot tub shock: how long to wait covers chlorine and non-chlorine shock in both kinds of tub.

After a shock, use "Mark as added" in Spa Calc, and it reminds you when to retest.

How to keep the smell from coming back

  • Keep sanitizer in range every day, not just after a soak.
  • Shock regularly and after heavy use.
  • Shower before soaking. CDC says rinsing off for one minute removes most of the dirt and other things on your body, and those are what form chloramines.
  • Keep pH in range. Low pH appears in two of the three smell causes on the chart above.
  • Change the water on schedule and clean the filter as its maker recommends.

When can you get in?

Not until you've tested. Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels. For questions about your health, ask your doctor.

Common mistakes

  • Treating a chlorine smell as "too much chlorine". It is usually chloramines, and the fix is a shock.
  • Masking the smell. Scented products don't change the water chemistry. Use plain, unscented bleach for chlorine doses.
  • Shocking with the cover closed. Leave it open while the jets run.
  • Skipping the drain. If a shock clears the smell for only a day or two, the water or the plumbing needs a fresh start.
  • Forgetting when you last shocked or drained. Spa Calc keeps your tests, doses and notes in one log, with a countdown to the next drain.

Track it in Spa Calc

Spa Calc works out each chlorine, bromine or shock dose for your tub's volume and product, checks whether your readings are ready to soak, and counts down to the next drain. Get Spa Calc for iPhone and log your next test.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

Why does my hot tub smell?

Most hot tub smells come from the water chemistry: too little sanitizer, a build-up of sweat, skin oils and other organics, combined chlorine (chloramines), or low pH. Test free chlorine (or bromine) and pH first. A shock, a sanitizer top-up and a pH correction fix most smells; if the smell keeps coming back, drain, clean and refill.

Why does my hot tub smell like chlorine?

A strong chlorine smell usually doesn't mean too much chlorine. CDC explains that the smell people call chlorine is probably chloramines, which form when chlorine combines with sweat, dirt, skin cells, deodorant and makeup. One hot tub maker's troubleshooting chart lists high chloramines and low pH as the causes, and shocking and correcting pH as the fix.

Why does my hot tub smell musty?

One hot tub maker's troubleshooting chart traces a musty odor to bacteria or algae growth. Shock the tub with sanitizer, and if the problem is visible or keeps coming back, drain, clean and refill it.

How do I get rid of a bad smell in my hot tub?

Test, then shock: raise free chlorine to 10 ppm with no stabilizer in the water (in a 400 gallon tub, from 1 ppm that takes about 7.4 fl oz (220 mL) of 6% bleach), run the jets with the cover open, and correct pH. Bleach strength varies, so use the calculator with the percentage on your label, and follow the product label. If the smell returns quickly, drain, clean and refill.

Is it safe to use a hot tub that smells?

A smell is a sign the water needs attention, so test before you get in. We use hot tub limits based on CDC guidance: Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels. For questions about your health, ask your doctor.