The quick answer: if your hot tub chlorine is too high, don't get in yet. Above 5 ppm free chlorine, wait and retest; never soak above 10 ppm. To bring it down, stop adding chlorine, take the cover off and run the jets. If you need it lower sooner, a chlorine reducer (sodium thiosulfate) works in minutes: about 0.38 oz (11 g) lowers free chlorine from 8 to 4 ppm in a 400 gallon tub. Add it in small steps, retest between them, and follow the product label.
The ready-to-soak checker below compares your readings with those limits: soak, wait, or fix first.
How high is "too high" in a hot tub?
We use hot tub limits based on CDC guidance and EPA product labels:
| Free chlorine (ppm) | What it means |
|---|---|
| Below 3 | Too low. Add chlorine before soaking. |
| 3 to 5 | Ready, if pH is in range. |
| Above 5 up to 10 | Too high to soak. Wait and retest. |
| Above 10 | Never get in. Lower it first. |
Where these come from:
- 3 ppm minimum. CDC recommends at least 3 ppm chlorine in hot tubs.
- 5 ppm soak maximum. One EPA-registered sodium hypochlorite label reads: "Re-entry into treated spas/hot tubs is prohibited at levels above 5 ppm chlorine". Check the label on the product you use.
- 10 ppm. CDC's advice for hot tub users is to talk to the operator or owner if chlorine reads above 10 ppm.
If your tub uses dichlor, your stabilizer (CYA) matters too: CDC recommends not using cyanuric acid in hot tubs at all, and we suggest draining and refilling once CYA is above 40 ppm.
Check the reading first
A surprising "too high" reading is worth a retest before you treat:
- High chlorine can read low. CDC notes that above 10 ppm a DPD test can partially or totally bleach out and read falsely low or 0. Taylor Technologies suggests diluting the sample 1:1 with chlorine-free water and multiplying the result by 2.
- Strips vs drops. CDC notes that test strips are less accurate than DPD test kits. Hot tub test strips vs drops explains when a strip can bleach out.
- Free vs total chlorine. Make sure you are reading free chlorine (FC). More on total chlorine below.
Why hot tub chlorine gets too high
- A shock. A chlorine shock raises the level well above the soak range on purpose. See hot tub shock: how long to wait.
- A dose sized for a bigger tub. Small tubs move fast: the same scoop raises a 250 gallon inflatable much more than a 500 gallon acrylic spa. Check your volume with how many gallons in a hot tub, using the maker's figure for your model.
- A floater, feeder or salt system set too high. It keeps adding chlorine on days the tub isn't used.
- The cover stayed on. CDC lists sunlight and hot tub jets that create droplets or mists as things that reduce chlorine. With the cover on and the jets off, chlorine lasts longer.
How to lower hot tub chlorine
Option 1: let it fall (free, slower).
- Stop adding chlorine. Take tablets out of the floater, or turn a salt system's output down.
- Take the cover off and run the jets, with the air controls open if your tub has them.
- Retest in an hour or two, and again before anyone gets in.
Option 2: chlorine reducer (fast).
Sodium thiosulfate, sold as chlorine reducer or chlorine neutralizer, removes chlorine within minutes.
- Test FC and decide where to stop: about 4 ppm, never below 3 ppm.
- Work out the amount. For reference, it takes about 2.7 g to lower FC by 1 ppm in 400 gallons, and 13.3 g to lower it by 5 ppm in 1,500 litres. The hot tub chemical calculator works it out for your tub.
- Follow the product label. Products differ in form and strength, so the label's rate comes first.
- Add half, run the jets for 15 minutes and retest. Add more only if FC is still above 5 ppm.
In a small tub, the amounts are tiny and easy to overshoot. Log each dose in Spa Calc for iPhone, and its soak card tells you when to retest and when the tub is ready.
Option 3: replace some water. Draining part of the tub and topping up with fresh fill water dilutes the chlorine. It is a good choice when the tub is due for a drain anyway. See how often to drain a hot tub.
Hot tub total chlorine too high
Total chlorine (TC) is free chlorine plus combined chlorine (CC): TC − FC = CC. If FC is in range but TC is much higher, the extra is combined chlorine, the leftovers from sweat and other contaminants. TroubleFreePool's Pool School describes CC as a sign that something in the water is still being broken down. The fix is an oxidizing shock, not a reducer: see hot tub shock.
Chlorine too high and pH reading odd
Taylor Technologies notes that chlorine above about 10 ppm can turn the phenol red pH test blue or purple instead of yellow-to-red. Add one drop of the chlorine neutralizer from your alkalinity test to the pH sample and retest. If pH is still low once chlorine is back in range, see hot tub pH too low.
When can you get back in?
Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels.
For questions about symptoms or your health, ask your doctor.
Common mistakes
- Getting in to "use up" the chlorine. Lower it first, then soak.
- Neutralizing in one go. Split the reducer dose and retest, or you'll be adding chlorine back.
- Keeping the cover on to wait it out. Cover off and jets on bring it down faster.
- Using a reducer when CC is the problem. High total chlorine with normal free chlorine needs a shock.
- Forgetting what went in. Spa Calc keeps every reading and dose in one log, so you can see whether the spike came from a shock, the floater or a doubled dose.
Track it in Spa Calc
Spa Calc sizes every chlorine and reducer dose for your tub's real volume, and its "ready to soak" card shows green, amber or red from your last test, with a countdown while you wait after a dose. Download Spa Calc for iPhone and log your next test.
One hot tub? Every feature, free. No account, no ads, and iCloud backup is included.
Sources
- CDC: What You Can Do to Stay Healthy in Hot Tubs: chlorine at least 3 ppm; talk to the operator or owner above 10 ppm; pH 7.0–7.8.
- CDC: Home Pool and Hot Tub Water Treatment and Testing: sunlight and hot tub jets reduce chlorine; DPD tests can bleach out above 10 ppm; test strips are less accurate than DPD kits; no cyanuric acid in hot tubs.
- EPA: sodium hypochlorite solution 12.5% label (PPLS): "Re-entry into treated spas/hot tubs is prohibited at levels above 5 ppm chlorine".
- TroubleFreePool Pool School: Free Chlorine: chlorine neutralizers contain sodium thiosulfate.
- TroubleFreePool Pool School: ABC's of Pool Water Chemistry: combined chlorine as a sign of contaminants still being broken down.
- Taylor Technologies: Why Am I Getting Unusual Test Results?: diluting a bleached-out DPD sample; chlorine over about 10 ppm turns phenol red blue or purple; one drop of chlorine neutralizer fixes the pH sample.
- Every dose on this page comes from the same chemistry engine as Spa Calc.
Safety
- Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
- Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
- Add chemicals to water, never water to chemicals.
- Store chemicals sealed, cool and dry, apart from each other.
- Read and follow the product label. It always comes first.