Chlorine

How Often to Add Chlorine to a Hot Tub

How often to add chlorine to a hot tub: test before each soak and top up when free chlorine runs low. What labels and CDC say, with doses for your tub.

Jump to the calculator

On this page
  1. Why there isn't one number
  2. What CDC and the labels say
  3. A simple routine
  4. How much to add each time
  5. How your choice of chlorine changes the routine
  6. If you're away, or the tub sits unused
  7. Common mistakes
  8. Track it in Spa Calc
  9. Sources
  10. Safety

The quick answer: there is no fixed calendar for how often to add chlorine to a hot tub. Test before each soak, and at least twice a day as CDC advises, and add chlorine whenever free chlorine (FC) is under 3 ppm. For a tub in regular use, that usually means a small dose daily or after each soak. Follow the product label.

Hot tub chlorine calculator

gal

Not sure? Find your tub’s volume.

%
ppm

Fresh water: 0. Dichlor raises it about 0.9 ppm per 1 ppm of chlorine.

ppm
ppm

Set from your CYA until you change it. Hot tubs: 3 to 5 ppm (CDC minimum 3; many labels say not to soak above 5).

Add

0.29oz

of Dichlor granules 56%

8.1 gabout 1⅞ tsp by volume

Raises free chlorine from 1 ppm to 4 ppm in 400 gal.

  • Side effects: CYA +2.7 ppm, TA −1.1 ppm.
  • Also raises cyanuric acid (stabilizer). It only comes down by replacing water.
  • Run the jets with the lid open and wait at least 15 minutes (20 after pH decreaser) before anyone gets in.
  • Pour it slowly in front of a return jet with the pump running.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

Use dichlor for the first week or two until stabilizer reaches about 30 ppm.

Save this test and get a reminder before your next soak.

Download on the App Store

Why there isn't one number

Chlorine demand follows use, not the calendar. A tub that sits covered and empty loses chlorine slowly. A tub used by four people on Saturday night may need a dose that same evening. CDC's hot tub Legionella toolkit notes that hot tubs speed up the decay of disinfectants.

So a schedule of "twice a week" can leave you short after a busy day and overdosed after a quiet week. A test tells you where you stand.

What CDC and the labels say

Source What it says
CDC, home pools and hot tubs Test chlorine and pH at least twice per day; more often when many people use the tub. Keep at least 3 ppm in hot tubs.
CDC, Legionella toolkit Test at least twice per day, as often as hourly in heavy use. Written for public tubs.
Registered dichlor label (Spa 56) Add daily or as necessary to hold the residual. Check often with a reliable test kit.
Registered dichlor label (BioGuard Master Dichloro Dihydrate) Hold 3 to 5 ppm. Test regularly. A shock dose may be needed nightly in a heavily used spa and weekly in a moderately used one.
Registered 10% liquid chlorine label (HTH) Hold 3 to 5 ppm. Shock after each use. Add a smaller dose daily during long periods without use.
TroubleFreePool hot tub basics Test free chlorine daily and add liquid chlorine as needed.

These are examples of what labels say, not recommendations for a specific product. Your own label decides.

A simple routine

  1. Before each soak: test FC and pH. Aim for 3 to 5 ppm FC, with pH 7.2 to 7.8.
  2. After each soak: add chlorine to replace what was used, with the jets running and the cover off. See after-soak dosing for how much.
  3. Through the day: CDC says to test at least twice per day, even if nobody got in. Top up if the reading is under 3 ppm.
  4. Every week or so: check alkalinity, and test CYA if you use dichlor.
  5. On schedule: drain and refill. See how often to drain a hot tub.

Log each test and dose in Spa Calc for iPhone, and after a couple of weeks you can see your tub's own pattern: how much a soak uses and how fast the reading falls on quiet days.

How much to add each time

To raise FC from 2 to 4 ppm:

Tub volume 56% dichlor granules 6% bleach 8.25% bleach
200 gal (757 L) 2.7 g 0.83 fl oz (24 mL) 0.58 fl oz (17 mL)
300 gal (1,136 L) 4.1 g 1.2 fl oz (37 mL) 0.87 fl oz (26 mL)
400 gal (1,514 L) 5.4 g 1.7 fl oz (49 mL) 1.2 fl oz (34 mL)

US household bleach is sold at 6–8.25%, and other countries' bleach is often weaker. Use plain, unscented bleach, and use the chlorine calculator with the percentage on your label. Follow the product label for any chlorine you use.

For the rest of the amounts, see how much chlorine to add to a hot tub.

How your choice of chlorine changes the routine

Bleach or liquid chlorine adds no stabilizer. CDC recommends not using cyanuric acid or chlorine products that contain it in hot tubs, because it slows disinfection. Without stabilizer the reading fades faster, so expect to top up more often.

Dichlor granules hold the reading a little longer because they add CYA, but CYA climbs with each dose. Above 40 ppm CYA, drain and refill. Many owners use dichlor for the first days of a fresh fill, then switch to bleach.

Chlorine tablets (trichlor) are made for pools. See how much chlorine for a hot tub for why we don't use them here.

Non-chlorine shock (MPS) isn't a sanitizer top-up. It helps oxidize what soakers leave behind, and how often you use it depends on your label and how much the tub gets used. The MPS shock calculator sizes the dose.

If you're away, or the tub sits unused

Chlorine keeps fading in a tub nobody uses, just more slowly. One registered liquid chlorine label gives a small daily dose during long periods without use, to hold 3 ppm. Test when you get back and bring the reading up before anyone soaks.

If the reading drops much faster than usual when nobody has been in the tub, check for a dirty filter or old water. Hot tub smells and cloudy hot tub water cover the next steps.

When can you soak? Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels.

Common mistakes

  • Adding chlorine on a set day, whatever the test says. It can leave the tub low after a busy day and high after a quiet one.
  • Adding more without testing first. Above 5 ppm, the fix is to wait, not to soak. See hot tub chlorine too high.
  • Copying a dose from a bigger tub. A dose for 400 gallons can overshoot a small inflatable by a lot. A wooden tub with no filter has its own routine: see wood-fired hot tub chlorine.
  • Ignoring CYA with dichlor. Your reading can look fine while the chlorine works more slowly.
  • Losing track of the last dose. Spa Calc keeps every dose in one log, so nothing goes in twice by accident.

Track it in Spa Calc

Spa Calc sizes each top-up for your tub's volume and chlorine strength, keeps your tests and doses in one log, and shows whether your reading is ready to soak. Get Spa Calc for iPhone and log your next test.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

How often should I add chlorine to my hot tub?

Most tubs in regular use need chlorine daily or after each soak, but your test decides. Test before every soak (CDC says at least twice a day), and add chlorine whenever free chlorine is under 3 ppm. One registered dichlor label says to add it daily or as necessary.

How often do I add chlorine to an inflatable hot tub?

On the same schedule: test before each soak and at least twice a day, as CDC advises, then add when the reading is low. Inflatable tubs hold less water, so one soak can move the reading more, and each dose must be smaller. Use your tub's real volume in the calculator.

How often do I add chlorine granules to a hot tub?

As often as the test calls for, usually daily or after use. In 400 gallons, raising free chlorine from 2 to 4 ppm takes about 5.4 g of 56% dichlor. Follow the product label, and keep an eye on CYA, which rises with every dichlor dose.

How often should I add chlorine tablets to a hot tub?

We don't use trichlor tablets in hot tubs. They are very acidic and add stabilizer. CDC recommends not using cyanuric acid or products that contain it in hot tubs. Use bleach or liquid chlorine, or dichlor granules for a short start-up period.

How long after adding chlorine can I get in a hot tub?

Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels.