Sanitizer

Hot Tub Start Up Chemicals: Step by Step

Hot tub start up chemicals in order: fill, alkalinity, pH, calcium, then chlorine or bromine. How much for 400 gallons and when the first soak is ready.

Jump to the calculator

On this page
  1. What you need on hand
  2. Step 1: Clean and fill
  3. Step 2: Total alkalinity
  4. Step 3: pH
  5. Step 4: Calcium hardness (soft water only)
  6. Step 5: Sanitizer last
  7. Step 6: Test before the first soak
  8. Inflatable hot tubs
  9. Common mistakes
  10. Track it in Spa Calc
  11. Sources
  12. Safety

The quick answer: hot tub start up chemicals go in one at a time, in this order: total alkalinity, then pH, then calcium hardness if your water is soft, and the sanitizer last. For chlorine, bringing a fresh 400 gallon tub to 4 ppm takes about 0.38 oz (11 g) of 56% dichlor. For bromine, you first build a bromide reserve, then turn part of it into bromine. Test before the first soak, and follow the product label for every chemical.

The calculator below sizes each step for your tub's volume and your product's strength.

All-in-one hot tub calculator

gal

Not sure? Find your tub’s volume.

ppm
ppm
ppm
ppm
ppm

Dichlor adds it. Blank if you have not tested.

°F
%

Not safe: do not get in yet.

Two things to fix. Start with ph.

  1. pH 7.9 → 7.5

    Lower it

    Add

    0.42oz

    of Dry acid / pH minus (sodium bisulfate 93%)

    12 gabout 2⅛ tsp by volume

    • Side effects: TA −3 ppm.
    • Run the jets with the lid open and wait at least 15 minutes (20 after pH decreaser) before anyone gets in.
    • Never add acid and chlorine together or in the same spot: mixing them releases toxic chlorine gas. Let the first one circulate before adding the other (the wait is shown on each step).

    Then wait 15 minutes with the jets running.

  2. Free chlorine 1 ppm → 4 ppm

    Raise it

    Add

    0.29oz

    of Dichlor granules 56%

    8.1 gabout 1⅞ tsp by volume

    • Side effects: CYA +2.7 ppm, TA −1.1 ppm.
    • Also raises cyanuric acid (stabilizer). It only comes down by replacing water.
    • Run the jets with the lid open and wait at least 15 minutes (20 after pH decreaser) before anyone gets in.
    • Free chlorine is below the minimum for your stabilizer level.
    • Use dichlor for the first week or two until stabilizer reaches about 30 ppm.

In range

  • CYA 20 ppm
  • TA 70 ppm
  • Use dichlor for the first week or two until stabilizer reaches about 30 ppm.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

  • CDC recommends not using stabilizer (cyanuric acid) in hot tubs, because it slows chlorine down. The dichlor-then-bleach method keeps it to about 30 to 40 ppm; bleach only keeps it at zero.

Save this test and get a reminder before your next soak.

Download on the App Store

What you need on hand

  • A test kit for sanitizer, pH and total alkalinity (TA). CDC notes that test strips are less accurate than drop kits, so a drop kit is worth having for start-up.
  • Alkalinity increaser (sodium bicarbonate).
  • pH increaser (soda ash) and pH decreaser (sodium bisulfate).
  • Calcium increaser, if your fill water is soft.
  • A sanitizer: chlorine or bromine (see below). If you're not sure which, see bromine vs chlorine for hot tubs.
  • A metal sequestrant (optional), for well water or water with iron or copper.
  • A clean filter and a hose pre-filter.

Starter kits sold with new tubs usually contain a version of this list. Check the strengths on each label, because the dose depends on them.

Step 1: Clean and fill

If you are replacing old water, how to drain a hot tub covers the steps before this one.

  1. Clean the shell before filling. CDC's hot tub guidance says to scrub all surfaces each time the tub is drained.
  2. Fill through the filter compartment. Jacuzzi's setup guide says to put the hose in the filter well, which helps keep air out of the plumbing. Fill to the level your manual shows.
  3. Use a hose pre-filter. Both Jacuzzi and Master Spas recommend one, to catch metals and sediment from the fill water.
  4. Watch softened water. Master Spas says never to use more than 50% softened water, because very soft water can foam and makes pH unstable.
  5. Add a metal sequestrant now if you use one. Master Spas adds it while filling and lets the water circulate for at least 30 minutes before the next chemical.

Turn the power on only once the tub is full, then start the pumps and heater. Jacuzzi's guide starts the chemistry once the water is at least 80°F (27°C).

Step 2: Total alkalinity

Test TA first. It's the buffer that holds pH steady, so getting it right makes the pH step much easier.

  • Ranges differ by maker: Jacuzzi's setup guide gives 80–120 ppm, and Master Spas gives 80–150 ppm. Use your own manual's range.
  • Too low: add alkalinity increaser. In a 400 gallon tub, going from 40 to 80 ppm takes about 3.6 oz (102 g) of baking soda (sodium bicarbonate). Follow the product label.
  • Too high: see hot tub alkalinity high, pH low for the acid-and-aeration method.

Run the jets, wait, and retest before moving on.

Step 3: pH

Both makers above aim for pH 7.2–7.6 during balancing. Soaking is fine at 7.2–7.8, the hot tub range based on CDC guidance.

We don't give a fixed pH decreaser amount, because it depends on your alkalinity. The pH and alkalinity calculator works it out from your readings.

Step 4: Calcium hardness (soft water only)

Jacuzzi's guide gives 150–250 ppm and Master Spas 180–250 ppm. If your fill water is well below that, add calcium increaser by the label. If it's already in range or above, skip this step.

Write down each reading as you go. Logging them in Spa Calc for iPhone keeps your start-up numbers together, so the next refill is quicker.

Step 5: Sanitizer last

Chlorine start-up

Add chlorine to reach 3–5 ppm free chlorine. For a fresh tub at 0 ppm:

Tub size 56% dichlor to 4 ppm 6% bleach to 4 ppm 8.25% bleach to 4 ppm
300 gal (1,136 L) 0.29 oz (8.1 g) 2.5 fl oz (73 mL) 1.7 fl oz (52 mL)
400 gal (1,514 L) 0.38 oz (11 g) 3.3 fl oz (98 mL) 2.3 fl oz (69 mL)
500 gal (1,893 L) 0.48 oz (14 g) 4.1 fl oz (122 mL) 2.9 fl oz (86 mL)

US household bleach is sold at 6–8.25%, and other countries' bleach is often weaker. Use plain, unscented bleach, and use the calculator with the percentage printed on your label.

Dichlor or bleach? Dichlor adds stabilizer (cyanuric acid, CYA) with every dose. CDC recommends not using cyanuric acid or stabilized chlorine products in hot tubs, because they slow disinfection. Many owners start with dichlor and switch to bleach before CYA builds up; using bleach only, with no stabilizer, is the other option. Above 40 ppm CYA, drain and refill. How much chlorine for a hot tub covers the daily routine.

Bromine start-up

Starting a hot tub with bromine takes two parts on a fresh fill:

  1. Build the bromide reserve with sodium bromide: 2.1 oz (59 g) in a 400 gallon tub.
  2. Add a small oxidizer dose to turn some of it into bromine: 0.57 oz (16 g) of 45% MPS (non-chlorine shock) brings a 400 gallon tub to about 5 ppm.

Don't use a full label shock dose on a fresh reserve. In 400 gallons, a full dose (3 oz (85 g)) would read about 27 ppm, far above the 8 ppm maximum. Then keep bromine at 4–6 ppm with tablets in a floater or feeder, set as the label says. How much bromine to add to a hot tub has the full routine.

Step 6: Test before the first soak

Let the water circulate as your manual says. Jacuzzi's setup guide, for example, allows 24 hours with the cover on before the first soak. Then test sanitizer and pH.

Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels.

After the first soak, add sanitizer to cover what was used, and test again before the next one. See how often to add chlorine to a hot tub for the routine from here. Mark each dose as added in Spa Calc, and it reminds you when to retest.

Inflatable hot tubs

The steps are the same, but the volume is much smaller, so doses are smaller too. Take the litres from your manual, not a guess. Inflatable hot tub chemicals has a dose table by size.

Common mistakes

  • Adding everything at once. Chemicals added together are hard to read on a test, and some must never be mixed. One at a time, with the jets running.
  • Sanitizer before balancing. Chlorine and bromine work best once pH is in range, which is why makers put them last.
  • Guessing the volume. A dose meant for 400 gallons can overshoot a smaller tub by a lot. See how many gallons in a hot tub.
  • A full shock dose on a fresh bromine fill. It can push bromine far above the soak limit.
  • Losing the start-up numbers. Spa Calc keeps every reading and dose in one log, with a countdown to the next drain.

Track it in Spa Calc

Spa Calc sizes each start-up dose for your tub's volume and product strength, checks whether your readings are ready to soak, and counts down to the next drain so you know when the next start-up is due. Get Spa Calc for iPhone and log your first test. When it's time to refill, see how often to drain a hot tub.

One hot tub? Every feature, free. No account, no ads, and iCloud backup is included.

Sources

  • Jacuzzi: Beginner's Guide to Setting Up Your Jacuzzi: use a hose filter; fill through the filter well; start chemistry once water is at least 80°F; order TA, pH, calcium, sanitizer last; TA 80–120 ppm, pH 7.2–7.6, calcium 150–250 ppm; 24 hours of circulation with the cover on before the first soak.
  • Master Spas: Quick Start Water Care Guide: hose pre-filter; no more than 50% softened water; metal sequestrant while filling, then 30 minutes of circulation; TA 80–150 ppm, pH 7.2–7.6, calcium 180–250 ppm; one chemical at a time and retest.
  • CDC: Controlling Legionella in Hot Tubs: free chlorine 3–10 ppm, bromine 4–8 ppm, pH 7.2–7.8; scrub all surfaces each time the tub is drained; cyanuric acid or stabilized chlorine products should not be used in hot tubs.
  • CDC: Home Pool and Hot Tub Water Treatment and Testing: at least 3 ppm chlorine in hot tubs; no cyanuric acid in hot tubs; test strips are less accurate than DPD kits.
  • Every dose and limit on this page comes from the same chemistry engine as Spa Calc.

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

What chemicals do I need to start up a hot tub?

A test kit, an alkalinity increaser and a pH increaser or decreaser, a calcium increaser if your water is soft, and a sanitizer: chlorine (dichlor granules or unscented bleach) or bromine (sodium bromide plus an oxidizer such as non-chlorine shock, then bromine tablets). Many owners also add a metal sequestrant while filling. Follow each product's label.

What order do you add hot tub start up chemicals?

Jacuzzi's setup guide gives the order as total alkalinity, then pH, then calcium hardness, and sanitizer last. Add one chemical at a time with the jets running, and retest before the next one.

How much chlorine do I put in a hot tub the first time?

To bring a fresh 400 gallon tub from 0 to 4 ppm takes about 0.38 oz (11 g) of 56% dichlor, or about 3.3 fl oz (98 mL) of 6% household bleach. US household bleach is 6–8.25%, so use the calculator with the percentage on your label. Then test: soak only at 3 to 5 ppm.

How do you start up a bromine hot tub?

Balance alkalinity and pH, then add sodium bromide to build the bromide reserve (2.1 oz (59 g) in 400 gallons), then a small oxidizer dose to turn some of it into bromine (0.57 oz (16 g) of 45% MPS brings it to about 5 ppm). Keep it up with bromine tablets in a floater or feeder.

How long after start up chemicals can I use my hot tub?

Follow your manual and the product labels. Then test before the first soak. Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels.