A round hot tub with blue-teal water, a stone rim and rolled towels beside palms

Draining

How to Drain a Hot Tub

How to drain a hot tub step by step: flush the lines, turn off the power, drain by hose or pump, dispose of the water safely, clean and refill.

Jump to the calculator

On this page
  1. Before you start
  2. How to drain it, step by step
  3. Why draining matters
  4. Common mistakes
  5. Track it in Spa Calc
  6. Sources
  7. Safety

The quick answer: to drain a hot tub, turn off the power at the breaker, open the drain valve with a garden hose attached (or use a submersible pump), and send the water somewhere your local rules allow. Clean the shell and filter while it is empty, refill through the filter compartment, and balance the water before anyone gets in. Most of the time goes on the cleaning and the new chemistry, not the draining itself.

How often you need to do this depends on size and use. A 400 gallon tub used by two people a day comes out at about 67 days between drains. Work out yours below.

Drain interval calculator

gal

Not sure? Find your tub’s volume.

Two people every evening = 2. Four people at the weekend only = about 1.1.

gal/min

Time how long a 5 gal (20 L) bucket takes to fill from your hose or pump.

67days

between drains

about 2.2 months

400 gal ÷ 3 ÷ 2 soakers a day = 67 days.

  • Draining at this rate takes about 1.3 hours. Refilling with a hose takes about as long again.
  • Drain sooner if the water stays cloudy or foamy after shocking, smells even when sanitizer is in range, or if CYA climbs above 40 ppm.
  • Flush the plumbing with a line cleaner before you drain, then clean the filter.

Save this test and get a reminder before your next soak.

Download on the App Store

Before you start

Pick a mild day. In freezing weather an empty tub and its pipes can be damaged, and Hot Spring's manual says to follow its winterizing steps instead. Hot tub in winter covers when to keep a tub running and when to winterize it. Have a garden hose, a clean filter or filter cleaner, a soft cloth and a test kit ready.

If you plan to use a line flush product, add it the day before or a few hours before you drain, as its label says. Jacuzzi's draining instructions recommend this to clear biofilm from the plumbing, so it leaves with the old water instead of seeding the new. If loose flakes show up in the water, hot tub white flakes explains what they are. Follow the product label.

How to drain it, step by step

Step 1: Test the water and note the readings. You'll want to know the sanitizer level before the water goes onto a lawn or down a drain, and a last log of the old water is useful for spotting a pattern later. Log it in Spa Calc for iPhone along with the drain date.

Test strips beside their closed container on a warm stone rim by blue-teal water

Step 2: Turn off the power at the breaker. Every manual we checked starts here. Jacuzzi warns that pumps or heaters running as the water drops can be badly damaged. Unplug plug-in and inflatable models too.

Step 3: Drain through the valve, or use a pump. On most acrylic tubs you attach a garden hose to the drain spigot and let gravity do the work. Hot Spring notes that a small amount of water stays in the lines afterward. Times from the makers:

  • Jacuzzi: about 45 to 90 minutes through the spigot, or about 10 to 15 minutes with a submersible pump for a standard tub.
  • Bullfrog: about 5 gallons per minute through a garden hose.

Inflatable tubs drain through a valve on the wall. Some makers sell a drain valve adapter that lets a hose fit it; Intex, for example, lists one for its PureSpa models. Follow your owner's manual for how to open the valve and fold or dry the tub if you are storing it.

Step 4: Send the water to the right place. Warm, chlorinated or brominated water can harm streams and some plants, so many cities ban it from storm drains. The City of Portland asks owners to drain to the sanitary sewer or let the water soak into the ground, and allows a storm drain only as a last resort after the water has sat, cooled and lost its chlorine. Minnesota's pollution agency says to bring chlorine to a minimum before draining and to follow local rules. Bullfrog's manual asks for sanitizer below 0.5 ppm before draining onto plants. Check with your city or water utility.

Step 5: Clean the shell and the filter while it's empty. Wipe the shell with a soft cloth and plain water or a spa surface cleaner. Hot Spring's manual says not to use products with abrasives or solvents, and Bullfrog warns against cleaners that leave soap in the water, which turns into foam later (see hot tub foam). Rinse well. Soak or replace the filter cartridge as its maker says. Don't leave an empty acrylic tub uncovered in direct sun: Bullfrog says sunlight can damage an empty shell.

A cloudy glass of water beside a clear one on a warm stone rim

Step 6: Refill through the filter compartment. Close the drain valve first. Hot Spring and Jacuzzi both say to fill through the filter area, which helps prevent an air lock in the pump. Hot Spring also says to run the jets briefly once full to purge air. Turn the power back on only when the water is above the level the manual gives.

A round hot tub full of clear blue-teal water with a stone rim in low sun

Step 7: Rebuild the chemistry. Fresh water starts with no sanitizer. Test the fill water, adjust alkalinity and then pH, and add your sanitizer. Our hot tub start up chemicals guide has the full order, and how much chlorine for a hot tub has the doses. Follow the product label.

A closed plain bottle on a warm stone rim beside blue-teal hot tub water

Step 8: Test before the first soak. Soak when free chlorine is 3 to 5 ppm and at least 7.5% of your CYA (bromine 4 to 6) and pH is 7.2 to 7.8, at least 15 minutes after adding anything (20 after pH decreaser); after chlorine, bromine or a shock, test again first. Above 5 ppm chlorine or 6 ppm bromine, wait and retest in an hour or two; never soak above 10 ppm chlorine or 8 ppm bromine, or with pH below 7.0 or above 7.8. Below 3 ppm chlorine (4 bromine), add sanitizer first; at pH 7.0 to 7.2, raise pH first; with CYA above 40 ppm, drain and refill. Hot tub limits based on CDC guidance and EPA product labels.

Why draining matters

CDC's hot tub guidance for operators lists "drain, scrub, clean, and fill" as routine care, and names biofilm in the plumbing as one of the conditions that help Legionella grow. CDC's Legionella page also asks for water to be replaced as the health department or manufacturer recommends, not just topped up. The how often to drain a hot tub guide explains the formula, and the same one appears in CDC's toolkit.

Common mistakes

  • Leaving the power on. Turn it off at the breaker before the water drops.
  • Draining into the street. Storm drains often lead straight to streams. Check local rules first.
  • Using household cleaners on the shell. Soap left behind causes foam in the new water.
  • Refilling through the footwell. On acrylic tubs, fill through the filter area to avoid an air lock.
  • Forgetting the date. Spa Calc counts down to your next drain from your tub's size and use, so you don't have to remember it.

Track it in Spa Calc

Spa Calc works out your drain interval from your tub's volume and how often it's used, and keeps your tests and doses in one log, so the new water starts from a clean record. Get Spa Calc for iPhone and log your first test after the refill.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

How do you drain a hot tub?

Flush the lines the day before if you use a line flush product, turn off the power at the breaker, then drain through the drain valve with a garden hose or use a submersible pump. Clean the shell and filter while it is empty, refill through the filter compartment, and balance the water before the first soak.

How long does it take to drain a hot tub?

Jacuzzi's own instructions put it at about 45 to 90 minutes through the spigot and about 10 to 15 minutes with a submersible pump for a standard tub. Bullfrog's manual says its drain runs about 5 gallons per minute through a garden hose.

Where should I drain hot tub water?

Follow your local rules. Many cities ban chlorinated or warm water in storm drains. The City of Portland, for example, asks owners to drain to the sanitary sewer or let the water soak into the ground, and Minnesota's pollution agency says to get chlorine to a minimum first.

How often should I drain my hot tub?

The usual formula is (gallons ÷ 3) ÷ average bathers per day. A 400 gallon tub used by two people a day comes out at about 67 days.

Do I need to turn off the hot tub to drain it?

Yes. The maker manuals we checked all say to turn off the power at the breaker first. Pumps and heaters running as the water drops can be badly damaged.

Save this guide

How to Drain a Hot Tub: illustrated Spa Calc guide card

Download this guide as an image